My focus was to make this as nice/practical a "reliable/street driver" as possible.
Extra attention has been spent on (often overlooked) important items, such as;
a reliable self bleeding cooling system,
a/c climate& control plumbing,
WIRING!, and heat/sound insulation.
The engine is a mild (302) 5.0 balanced & assembled using all ARP fasteners & quality pieces
The car is currently "unfinished", with all the hard stuff done, and done right.
Here is a complete list of what is needed to finish the car:
sanden 508 a/c compressor, mounting bracket, and belt
pulse generator for the speedometer
finish welding/fabbing exhaust headers (65% done)
radiator hoses & clamps
heater control valve
cables for shifter,accel, and p-brake
accel pedal
interior upholstery (ie-carpet,seat covering)
battery, and alternator
final paintwork
All bodywork is done by a fiberglass guy with over 15 years exp.,,,,and body is in final primer. This body is nice and had alot of hours put into making it that way.
The car is ready to spray color on it!
I'm considering selling the car with two options:
#1: the buyer comes & gets the car "as is" and finshes it himself/herself.
#2: the buyer makes a deal with me & sends me a deposit,
and I'll have it painted the color of your choice and finish the assembly by an agreed date.
I'm talking 100 percent ready to drive anywhere,,, no overheating, no wiring issues, ice cold a/c, working heater.
For those who don't know, I have over 24 years experience as a Mercedes tech, have built numerous racecars,cobras,hotrods, and am an authorized builder for premier motorsports.
Only selling to raise funds for purchase of building.
see many detailed pics here, just click on GT40NZ part 1 and part 2 to see all the pics
web page
detailed specs:
BODY:
Fiberglass GT40 replication body from New Zealand.
Body has been prepped for paint and is in final primer.
Mods/fixes to body were:
#1 cut out and rebuilt nose jamb area, then installed in the center of the front end (it was off originally)
#2 made a new dual nostril nose section
#3 removed the passenger side bump in the cowl(and front clip) for wiper (had 2 only need 1)
#4 many hours of fairing, filling,sanding to get all body panels to fit and line up properly
car has all needed lights, door handles, and exterior trim pieces
CHASSIS:
Powder painted “black chrome”
Left hand drive with center shift
1 inch dropped floor (steel)
adjustable steering column mount with heim joints
rollbar
clad in aluminum (& some stainless) paneling
all “through holes” in chassis re-inforced with a welded tube
SUSPENSION:
Tubular front control arms (double shear mounted)
Corrolla rack and pinion steering
Koni adjustable coil over shocks F&R
Heim joints used throughout
Most suspension pieces powder painted bright silver
Adjustable front and rear sway bars
BRAKES:
Tilton floor mounted pedal assembly, w/adjustabel F/R bias
Braided hoses at calipers
Wilwood dynalite and superlite 4 piston calipers
Wilwood p-brake calipers
Slotted and drilled front rotors, vented rear rotors
INTERIOR:
Vinyl covered dash and center console
Autometer carbon fiber gauges
Custom A/C heater control panel
Mercedes multi funtion switch(turn signal,hi-low beam, wiper,etc)
Mountney flat three spoke steering wheel w/custom machined hub (similar to original GT40)
Splined quick release for steering wheel
Carbon look shift handle
Mercedes dome light
Fiberglass “un upholstered” GT40 type seatshells
p-brake lever
tapered seat mounts
ELECTRIC&FUEL SYSTEMS:
mini fusebox
custom made harness by me, with drawings
relays for fuel pump, a/c, hi beam, lo beam, fog lights, and horn, & fans
all wiring covered.loomed , properly secured and grommeted
all wiring travels along pass side door sill.
Fuse box,relays, alt and batt all mount on pass side of car.
cenntech custom adjustable relay for fan
MSD ignition system mounted behind the seat
MSD coil and Mallory unilite dist
Engine firewall has a quick connectplug to disconnect all engine compartment wiring for engine.
edlebrock carb w/edelbrock fuel feed & inline filter
carter elec fuel pump
fuel press regulator
fuel switchover valve to operate left or right tanks
two ten gallon alum fuel tanks with explosafe material
two fuel filters mounted between tanks and fuel valve
top of door sills covered with stainless paneling and stainless rivits & seam sealer over fuel tanks
two fuel gauges
correct appearing GT40 fuel fillers, with a stock type cap underneath (similar to FFR fuel cap set up)
COOLING SYSTEM:
Brass 6 core radiator with dual fans
Stainless steel cooling lines for front to rear transfer
Bleed lines on top of radiator and on rear of intake manifold continuosly purge air to puke tank
Spun aluminum puke tank with Mercedes 20 pound cap
A/C&heater:
Vintage air condensor
Compact hot rod air evaporator/heater box
Custom control panel
All hoses which pass through a panel use bulkhead fittings
All A/C hoses professionally crimped
Front to rear transfer is by solid alum tubing on drivers door sill
Dash has four forward and two defrost ducts
Vacuum resevoir mounted in engine compartment and vacuum hardline is plumbed for heater control valve
WHEELS/TIRES:
Team 3 16 inch wheels w/z rated sumitomo HTRZ tires 255/50 rear and 205 front
ENGINE:
5.0 (302) balanced, assembled using ARP fasteners
Armondos GT40 oil pan
Canton oil filter adapter and oil filter housing
Trick flow heads w motorsport rocker arms
B303 cam
Stage 8 header bolts and alum header gaskets
Motorsport valve covers w stainless bolts
Powder painted edelbrock performer intake w stainless bolts
Explorer timing cover and water pump
Fidanza alum flywheel
Spec 10.5 inch clutch
Small starter
Hydraulic clutch
Renault (factory reman) transaxle
HD upgraded input shaft and custom shift linkage
MISC:
Door hold down brackets, F&R body stays, misc trim
Rare and expensive cibie headlights w/curved lens
All tail and marker lights,
3 different types of sound and heat insulation used depending on location.
This kit is:
in the USA (Kansas),
can be delivered to your door within a few days of transaction,
has had most of the expensive (hard) work already done,
needs minimal investment (less than $10k) to be completed,
and is NOT a mess someone has "given up" on.
see pics here:
web page
contact:
Alain (Alan) Vanhollebeke
avanhollebeke@cox.net
785 228 2440 daytime mon-fri
Extra attention has been spent on (often overlooked) important items, such as;
a reliable self bleeding cooling system,
a/c climate& control plumbing,
WIRING!, and heat/sound insulation.
The engine is a mild (302) 5.0 balanced & assembled using all ARP fasteners & quality pieces
The car is currently "unfinished", with all the hard stuff done, and done right.
Here is a complete list of what is needed to finish the car:
sanden 508 a/c compressor, mounting bracket, and belt
pulse generator for the speedometer
finish welding/fabbing exhaust headers (65% done)
radiator hoses & clamps
heater control valve
cables for shifter,accel, and p-brake
accel pedal
interior upholstery (ie-carpet,seat covering)
battery, and alternator
final paintwork
All bodywork is done by a fiberglass guy with over 15 years exp.,,,,and body is in final primer. This body is nice and had alot of hours put into making it that way.
The car is ready to spray color on it!
I'm considering selling the car with two options:
#1: the buyer comes & gets the car "as is" and finshes it himself/herself.
#2: the buyer makes a deal with me & sends me a deposit,
and I'll have it painted the color of your choice and finish the assembly by an agreed date.
I'm talking 100 percent ready to drive anywhere,,, no overheating, no wiring issues, ice cold a/c, working heater.
For those who don't know, I have over 24 years experience as a Mercedes tech, have built numerous racecars,cobras,hotrods, and am an authorized builder for premier motorsports.
Only selling to raise funds for purchase of building.
see many detailed pics here, just click on GT40NZ part 1 and part 2 to see all the pics
web page
detailed specs:
BODY:
Fiberglass GT40 replication body from New Zealand.
Body has been prepped for paint and is in final primer.
Mods/fixes to body were:
#1 cut out and rebuilt nose jamb area, then installed in the center of the front end (it was off originally)
#2 made a new dual nostril nose section
#3 removed the passenger side bump in the cowl(and front clip) for wiper (had 2 only need 1)
#4 many hours of fairing, filling,sanding to get all body panels to fit and line up properly
car has all needed lights, door handles, and exterior trim pieces
CHASSIS:
Powder painted “black chrome”
Left hand drive with center shift
1 inch dropped floor (steel)
adjustable steering column mount with heim joints
rollbar
clad in aluminum (& some stainless) paneling
all “through holes” in chassis re-inforced with a welded tube
SUSPENSION:
Tubular front control arms (double shear mounted)
Corrolla rack and pinion steering
Koni adjustable coil over shocks F&R
Heim joints used throughout
Most suspension pieces powder painted bright silver
Adjustable front and rear sway bars
BRAKES:
Tilton floor mounted pedal assembly, w/adjustabel F/R bias
Braided hoses at calipers
Wilwood dynalite and superlite 4 piston calipers
Wilwood p-brake calipers
Slotted and drilled front rotors, vented rear rotors
INTERIOR:
Vinyl covered dash and center console
Autometer carbon fiber gauges
Custom A/C heater control panel
Mercedes multi funtion switch(turn signal,hi-low beam, wiper,etc)
Mountney flat three spoke steering wheel w/custom machined hub (similar to original GT40)
Splined quick release for steering wheel
Carbon look shift handle
Mercedes dome light
Fiberglass “un upholstered” GT40 type seatshells
p-brake lever
tapered seat mounts
ELECTRIC&FUEL SYSTEMS:
mini fusebox
custom made harness by me, with drawings
relays for fuel pump, a/c, hi beam, lo beam, fog lights, and horn, & fans
all wiring covered.loomed , properly secured and grommeted
all wiring travels along pass side door sill.
Fuse box,relays, alt and batt all mount on pass side of car.
cenntech custom adjustable relay for fan
MSD ignition system mounted behind the seat
MSD coil and Mallory unilite dist
Engine firewall has a quick connectplug to disconnect all engine compartment wiring for engine.
edlebrock carb w/edelbrock fuel feed & inline filter
carter elec fuel pump
fuel press regulator
fuel switchover valve to operate left or right tanks
two ten gallon alum fuel tanks with explosafe material
two fuel filters mounted between tanks and fuel valve
top of door sills covered with stainless paneling and stainless rivits & seam sealer over fuel tanks
two fuel gauges
correct appearing GT40 fuel fillers, with a stock type cap underneath (similar to FFR fuel cap set up)
COOLING SYSTEM:
Brass 6 core radiator with dual fans
Stainless steel cooling lines for front to rear transfer
Bleed lines on top of radiator and on rear of intake manifold continuosly purge air to puke tank
Spun aluminum puke tank with Mercedes 20 pound cap
A/C&heater:
Vintage air condensor
Compact hot rod air evaporator/heater box
Custom control panel
All hoses which pass through a panel use bulkhead fittings
All A/C hoses professionally crimped
Front to rear transfer is by solid alum tubing on drivers door sill
Dash has four forward and two defrost ducts
Vacuum resevoir mounted in engine compartment and vacuum hardline is plumbed for heater control valve
WHEELS/TIRES:
Team 3 16 inch wheels w/z rated sumitomo HTRZ tires 255/50 rear and 205 front
ENGINE:
5.0 (302) balanced, assembled using ARP fasteners
Armondos GT40 oil pan
Canton oil filter adapter and oil filter housing
Trick flow heads w motorsport rocker arms
B303 cam
Stage 8 header bolts and alum header gaskets
Motorsport valve covers w stainless bolts
Powder painted edelbrock performer intake w stainless bolts
Explorer timing cover and water pump
Fidanza alum flywheel
Spec 10.5 inch clutch
Small starter
Hydraulic clutch
Renault (factory reman) transaxle
HD upgraded input shaft and custom shift linkage
MISC:
Door hold down brackets, F&R body stays, misc trim
Rare and expensive cibie headlights w/curved lens
All tail and marker lights,
3 different types of sound and heat insulation used depending on location.
This kit is:
in the USA (Kansas),
can be delivered to your door within a few days of transaction,
has had most of the expensive (hard) work already done,
needs minimal investment (less than $10k) to be completed,
and is NOT a mess someone has "given up" on.
see pics here:
web page
contact:
Alain (Alan) Vanhollebeke
avanhollebeke@cox.net
785 228 2440 daytime mon-fri